Browse Topic: Power electronics
The driving capability and charging performance of electric vehicles (EVs) are continuously improving, with high-performance EVs increasing the voltage platform from below 500V to 800V or even 900V. To accommodate existing low-voltage public charging stations, vehicles with high-voltage platforms typically incorporate boost chargers. However, these boost chargers incur additional costs, weight, and spatial requirements. Most mature solutions add a DC-DC boost converter, which results in lower charging power and higher costs. Some new methods leverage the power switching devices and motor inductance within the electric drive motor to form a boost circuit using a three-phase current in-phase control strategy for charging. This approach requires an external inductor to reduce charging current ripple. Another method avoids the use of an external inductor by employing a two-parallel-one-series topology to minimize current ripple; however, this reduces charging power and increases the risk
Due to the high-power density, high torque rating, low torque ripples and fault-tolerant capability, the Dual Three-Phase Permanent Magnet Synchronous Motor (DTP-PMSM) has recently emerged as a feasible alternative for automotive applications. However, it comes with its own challenge of increased losses at low torque due to the use of 6-phase inverter or two three-phase inverters. The DTP-PMSM drive model can be designed to function in two operating modes, double-channel (dual three-phase) mode with both the inverters operating, and single-channel (three-phase) with one of the two inverters shut down. This paper proposed an efficiency analysis between single channel and double channel modes in a DTP-PMSM drive. A simulation model is prepared to calculate efficiency, and the losses associated with different parts of battery fed DTP-PMSM drive system operated in both modes. Detailed loss model is simulated to represent efficiency of a battery-fed DTP-PMSM drive system. Both single
Heavy-duty vehicles, particularly those towing higher weights, require a continuous/secondary braking system. While conventional vehicles employ Retarder or Engine brake systems, electric vehicles utilize recuperation for continuous braking. In a state where HV Battery is at 100% of SOC, recuperated energy from vehicle operation is passed on to HPR and it converts electrical energy into waste heat energy. This study focuses on identification of routes which are critical for High Power Brake Resistors (HPRs), by analyzing the elevation data of existing charging stations, the route’s slope distribution, and the vehicle’s battery SOC. This research ultimately suggests a method to identify HPR critical vehicle operational routes which can be useful for energy efficient route planning algorithms, leading to significant cost savings for customers and contributing to environmental sustainability.
Balancing low conductivity, corrosion resistance and optimum heat transfer in next-generation EV coolants while meeting new EV safety regulations. Managing the heating and cooling of electric vehicle propulsion systems may seem to be an easy task compared with combustion engines. After all, ICEs run much hotter-the thermal optimum for a gasoline engine is around 212 F (100 C). By comparison, EV batteries normally generate (as a function of current during charge/discharge cycles) a relatively cool 59-86 F (15-30 C). And while motors and power electronics operate hotter, typically 140-176 F (60-80 C), they still run cooler than ICEs. But among the myriad complexities of EV thermal management are batteries' dislike for temperature extremes, new cell chemistries, heat-generating high-voltage electrical architectures and 800V fast charging. All are putting greater focus on maintaining stable EV battery thermal performance and safety. Experts note that compatibility among the cell chemistry
During a recent Bosch tech showcase, we spoke with Joe Dear, engineering manager for electric propulsion systems at Linamar. The Guelph, Ontario-based parts manufacturer is no stranger to building unsung components for the auto industry, including gears, camshafts, connecting rods, and cylinder heads. The Linamar team was demonstrating a modified Ram 2500, a collaboration between Bosch and Linamar, that was outfitted with a prototype electric powertrain and new e-axles: a rigid axle on the rear (with a Bosch motor and inverter) and a steering axle up front.
The study demonstrates the possibility and in particular the method to derive the efficiency of the entire fuel cell power system by measuring specific data of the recirculation path of the anode circuit of a fuel cell system. The results demonstrate the capabilities of the existing test rig and enable investigations on the suitability of auxiliary components. This study focuses on the hydrogen recirculation path equipped with multiple sensors and a needle valve to enable the required operating conditions of the fuel cell. Running a startup load profile without reaching the equilibrium state at all steps, the dynamic of the system and the requirements to the sensor parameters, such as sampling rate and precision, was seen. Additionally, it became obvious that the recirculation pump used is oversized, but a load point shift compensated this artifact. In detail, the stoichiometry and the efficiency of the entire system was evaluated. It was seen that the hydrogen concentration is
SAE J3072 establishes requirements for a grid support inverter system function that is integrated into a plug-in electric vehicle (PEV), which connects in parallel with an electric power system (EPS) by way of conductively coupled, electric vehicle supply equipment (EVSE). This standard also defines the communication between the PEV and the EVSE required for the PEV onboard inverter function to be configured and authorized by the EVSE for discharging at a site. The requirements herein are intended to be used in conjunction with IEEE 1547-2018 and IEEE 1547.1-2020 or later versions.
Future electric vehicles will be more efficient, more powerful, and will be able to hold more energy in their batteries than today’s EVs. Those big “mores” require countless small improvements beyond the headline component — batteries. One of the richest target areas is power-electronics technology and components used throughout the EV ecosystem. A new generation of power electronics will be found in tomorrow’s EVs, charging stations, and related infrastructure components.
General Motors (GM) is working towards a future world of zero crashes, zero emissions and zero congestion. It’s “Ultium” platform has revolutionized electric vehicle drive units to provide versatile yet thrilling driving experience to the customers. Three variants of traction power inverter modules (TPIMs) including a dual channel inverter configuration are designed in collaboration with LG Magna e-Powertrain (LGM). These TPIMs are integrated with other power electronics components inside Integrated power electronics (IPE) to eliminate redundant high voltage connections and increase power density. The developed power module from LGM has used state-of-the art sintering technology and double-sided cooled structure to achieve industry leading performance and reliability. All the components are engineered with high level of integration skills to utilize across TPIM variants. Each component in the design is rigorously analyzed and tested from component to system levels to ensure high
Inverter is the power electronics component that drives the electrical motor of the electrical driven compressor (EDC) and communicates with the car network. The main function of the inverter is to convert the direct current (DC) voltage of the car battery into alternating current (AC) voltage, which is used to drive the three-phase electric motor. In recent days, inverters are present in all automotive products due to electrification. Inverter contains a printed circuit board (PCB) and electronic components, which are mounted inside a mechanical housing and enclosed by a protective cover. The performance of the electrical drive depends upon the functioning of the inverter. There is a strong demand from the customer to withstand the harsh environmental and testing conditions during its lifetime such as leakage, dust, vibration, thermal tests etc. The failure of the inverter leads to malfunction of the product, hence proper sealing and validation is necessary for inverters to protect
Accelerated adoption of electric propulsion system in mobility industry has stressed the time and iterations of product development cycle which was traditionally known to go over multiple iterations and phases. Current market demands a timely introduction of compelling products that brings high value to end user. Further, a growing emphasis over reducing mineral content using sustainable options and process, adds further complexity to multi-objective-optimization of electric drive systems. At BorgWarner our engineers use Digital-Twins, physics-based models which closely represent BorgWarner products in greater dept (physics) thus allowing an improved assessment of product design (components and systems) to target application at very early stage in product development. The spring success with Digital-Twin, BorgWarner furthered enhanced the model through introducing Artificial Intelligent (AI) and Machine Learning (ML) technologies in both modelling and virtual sensing. This paper will
The automotive industry has seen accelerating demand for electrified transportation. While the complexity of conventional ICE vehicles has increased, the powertrain still largely consists of a mechanical system. In contrast, vehicle architectures in electrified transportation are a complex integration of power electronics, batteries, control units, and software. This shift in system architecture impacts the entire organization during new product development, with increased focus on high power electronic components, energy management strategies, and complex algorithm development. Additionally, product development impact extends beyond the vehicle and impacts charging networks, electrical infrastructure, and communication protocols. The complex interaction between systems has a significant impact on vehicle safety, development timeline, scope, and cost. A systems engineering approach, with emphasis on requirements definition and traceability, helps ensure decomposition of top level
This paper gives insights in the theoretical measurement uncertainty of E-Drive rotor position dependent results, like Id and Iq calculations, done by a modern propulsion power analyzer (PA). The calculation of Id and Iqis fundamental to perform control optimization and application tasks for an E-Drive system. To optimize the E-Drive system application towards e.g., best efficiency, best performance, or improved NVH the importance of the testing toolchain is described: a power analyzer delivering the required results, an automation system, and a Design of Experiment tool to set improved target values. Consequently, inverters applications featuring field-oriented control (FOC) with permanent magnet synchronous machines (PMSM) are updated with a chosen control strategy. For achieving a certain behavior of an E-Drive, different degrees of freedom in the Inverter Control Unit are available; Lookup tables Id and Iq represent two fundamental application labels to be considered. Since the
System optimization and lifecycle analysis are key to taking heavy rare earths out of next-gen motors for commercial EVs. All components of an electric propulsion system - the motor, battery pack and inverter, in particular - are interrelated and optimized for a system function. Still, there are significant trade-offs in cost and what's best for sustainability when developing today's e-drive systems, according to David Fulton, director of rotating electric machines, PowerDrive Systems at BorgWarner Inc. “The dominant design for motors today is probably the worst for sustainability in terms of KPIs [key performance indicators] as well as highest in cost. But it serves the greater good of the system [by enabling] the lowest cost for the battery pack and inverter,” Fulton said at the 2023 SAE COMVEC conference, during his presentation on next-gen motor technology for commercial vehicles.
Items per page:
50
1 – 50 of 440